Search found 9734 matches
- Mon 06 Feb, 2023 11:02 am
- Forum: Help!
- Topic: Extra large painting to frame
- Replies: 10
- Views: 18944
Re: Extra large painting to frame
Thank you very much for those replies! I very much like the wooden slip idea, and the raised edge to help restrict movement. It's not to restrict movement, just the opposite. If (when) the paper expands/contracts it can move freely and not go wavy. It should be hinged at the top with a few loose hi...
- Sun 05 Feb, 2023 7:03 pm
- Forum: Help!
- Topic: Antique Frame Style Name
- Replies: 4
- Views: 1202
Re: Antique Frame Style Name
Large ornate frames in the past where generally had a carcass built from sections. It isn't practical or desirable to mill a single billet of wood that may be six or more inches wide. Also a lot of saving in the weight of the frame can be gained by leaving voids here and there. The construction meth...
- Sun 05 Feb, 2023 6:47 pm
- Forum: Help!
- Topic: Extra large painting to frame
- Replies: 10
- Views: 18944
Re: Extra large painting to frame
If you want the look of a mount you could do something like this.... This was a charcoal drawing on mountboard which being more rigid than paper did not need a traditional mount. I used a very narrow moulding as a spacer and then did a flat wood panel as 'mount' that surrounded it. The outer frame g...
- Sun 05 Feb, 2023 6:37 pm
- Forum: Help!
- Topic: Extra large painting to frame
- Replies: 10
- Views: 18944
Re: Extra large painting to frame
There are sneaky ways I've used in the past to get around this. :wink: One is to use a slip as a mount and slightly raise the back edge of the slip to avoid crimping the edges which will restrict movement. Hard to explain in words, here's a piccy........ raisedslipmat001.jpg You hinge the piece onto...
- Thu 02 Feb, 2023 12:21 pm
- Forum: Help!
- Topic: Posters with no mount
- Replies: 7
- Views: 3688
Re: Posters with no mount
If the poster is drymounted to a board and glazing placed on top then chances are it will be OK if kept in a stable environment. Don't pay too much heed to 'acid-free' considerations as the poster itself if likely to be far more acidic to the materials it's in contact with. Only on replaceable items...
- Wed 01 Feb, 2023 11:07 am
- Forum: The Good, The Bad, And The Ugly
- Topic: The Ugly - Fixings and taping up the back...
- Replies: 11
- Views: 7308
Re: The Ugly - Fixings and taping up the back...
That's my go-to method with canvases. But I use the bendy plates from Lion. They have a bit of give in them.
I never tape over them.
I never tape over them.
- Wed 01 Feb, 2023 11:02 am
- Forum: Help!
- Topic: Mirrored glass
- Replies: 5
- Views: 2661
Re: Mirrored glass
As long as the frame is perfectly flat. 3mm glass will bend to fit in a warped frame and can produce weird
distortions. In clothes shops they would often wedge a matchstick under the rebate to make a 'slimming' mirror.
distortions. In clothes shops they would often wedge a matchstick under the rebate to make a 'slimming' mirror.
- Tue 31 Jan, 2023 10:48 am
- Forum: General Discussion
- Topic: Removing watermarks
- Replies: 6
- Views: 3508
Re: Removing watermarks
If you don't want your copyrighted images purloined, then don't put them on the web. Or put low-res versions up.
It's like leaving your car outside your house with the keys in and with a notice on saying "This is my car. It is a criminal act to take it away".
It's like leaving your car outside your house with the keys in and with a notice on saying "This is my car. It is a criminal act to take it away".
- Thu 26 Jan, 2023 4:47 pm
- Forum: Help!
- Topic: Corkboard supplier
- Replies: 2
- Views: 1018
Re: Corkboard supplier
Just Googled it and got lots of answers.
I used to make notice boards (for myself) using cork tiles. The scraps are very useful around the workshop.
I used to make notice boards (for myself) using cork tiles. The scraps are very useful around the workshop.
- Wed 18 Jan, 2023 10:43 am
- Forum: General Discussion
- Topic: Online Framing Tutorials
- Replies: 12
- Views: 9835
Re: Online Framing Tutorials
There is a wealth of clips on YouTube and some of it is very good. Mainly clips from equipment manufacturers/suppliers. You have to cherry-pick them though. As mentioned, a lot is from people who don't really know what they are talking about. I'm thinking of folks who think spray-glue is a good way ...
- Wed 18 Jan, 2023 10:37 am
- Forum: Introductions
- Topic: Hello from Prints of Thieves
- Replies: 5
- Views: 3961
Re: Hello from Prints of Thieves
Welcome Jamie.
- Mon 16 Jan, 2023 10:00 am
- Forum: Help!
- Topic: Mountboard moulding
- Replies: 3
- Views: 3854
Re: Mountboard moulding
That's what I would term a 'fillet'. :D Many suppliers make complimentary fillets that match a moulding (as appears to be the case there). LJ/Arcadia did a lot but not sure what they do atm as I hardly never buy finished moulding. You can always paint a plain wood one as YPF says. :wink: A black one...
- Thu 12 Jan, 2023 4:52 am
- Forum: Help!
- Topic: very thin wood wedges
- Replies: 5
- Views: 2691
Re: very thin wood wedges
You can buy 2mm ply (some on Amazon) All you need then is a saw.
Not as irksome as it sounds. A Japanese pull-saw and a guide jig will make short work.
Not as irksome as it sounds. A Japanese pull-saw and a guide jig will make short work.
- Wed 11 Jan, 2023 11:28 am
- Forum: Help!
- Topic: Underpinner advice please?
- Replies: 14
- Views: 4668
Re: Underpinner advice please?
You might consider using Ash rather than Oak. It is easier to underpin and more consistent in density. Oak is not easy to join as you can get localised hard sections. Stacking v-nails in Oak is not advisable. The best way with Oak is the old school glue/clamp/cross nail/fill. Or get a dovetail route...
- Mon 09 Jan, 2023 10:29 am
- Forum: After Hours
- Topic: What do you listen to when working?
- Replies: 23
- Views: 65689
Re: What do you listen to when working?
I have the TV on all day and night.
Classic comedies (that I have watched countless times before) all on USB sticks so no breaks. I can watch all Dad's Army from start to finish
uninterrupted. I say 'watch', it's more listen.
Classic comedies (that I have watched countless times before) all on USB sticks so no breaks. I can watch all Dad's Army from start to finish
uninterrupted. I say 'watch', it's more listen.
- Sun 08 Jan, 2023 11:38 am
- Forum: The Good, The Bad, And The Ugly
- Topic: Reusing an old frame.
- Replies: 4
- Views: 2305
Re: Reusing an old frame.
People tend to think once they have 'a frame' then all they need to do is have you fit their art in it and charge you a fiver. :lol: More often than not the old frame has problems and complications that makes it cheaper to make a new one. It's one thing to work on a nice frame that deserves restorat...
- Sun 08 Jan, 2023 11:31 am
- Forum: Help!
- Topic: Really Annoying
- Replies: 5
- Views: 1967
Re: Really Annoying
I've had that a few times. Best to copy the post before submitting.
- Sat 31 Dec, 2022 12:42 pm
- Forum: Help!
- Topic: 2x Canvasses
- Replies: 4
- Views: 2329
Re: 2x Canvasses
Why the double mat(mount)? Mat's are for paper art. Stretcher bars are for canvas. With a spacer/slip if glazed. I have stuck canvases down (small ones) but only if there is good reason. Those look OK for stretching, indeed they look as though they have previously been stretched. Sorry to carp. It j...
- Thu 22 Dec, 2022 10:57 am
- Forum: After Hours
- Topic: Merry Christmas to all.
- Replies: 1
- Views: 2487
Re: Merry Christmas to all.
And Seasons Greetings to you Mark.
- Sun 18 Dec, 2022 12:56 pm
- Forum: Help!
- Topic: Fabric print in a frame...most suitable method?
- Replies: 2
- Views: 972
Re: Fabric print in a frame...most suitable method?
I have in the past mounted fabrics to board by pre-mounting drymount FILM to the board, leaving the release paper on top (You could use sticky mounting board, but I didn't have any). When the board has cooled, peel the release paper and smooth/position the fabric onto the sticky surface. Put it back...