Search found 519 matches
- Thu 16 Jun, 2022 4:28 pm
- Forum: General Discussion
- Topic: Shortage of moulding stock at suppliers ....
- Replies: 15
- Views: 3693
Re: Shortage of moulding stock at suppliers ....
It may be a timber supply issue that is causing delays for the moulding manufacturers. I believe i am correct that many of factory finished mouldings use obeche. Latham's timber yard in Yate near Bristol is saying 6-8 weeks lead times for obeche stock. They are the only Latham's to stock obeche as t...
- Tue 14 Jun, 2022 9:13 pm
- Forum: Help!
- Topic: Aargh! Not enought moulding
- Replies: 9
- Views: 1299
Re: Aargh! Not enought moulding
Have you waxed it after painting. Liberon black bison neutral wax is the one i prefer. 2 coats and a good buff will give some sheen which may get it closer to the original.
Nick
Nick
- Mon 13 Jun, 2022 7:19 pm
- Forum: General Discussion
- Topic: Here's Something you might find Interesting
- Replies: 17
- Views: 3228
Re: Here's Something you might find Interesting
Very useful and interesting post Dermot. Many thanks for posting.
Nick
Nick
- Thu 02 Jun, 2022 12:30 pm
- Forum: Help!
- Topic: Silicone grrr
- Replies: 7
- Views: 1062
Re: Silicone grrr
If your artist wants it this way, fix the blocks to the canvas panel using CT1 adhesive rather than silicone. Then make your tray frame as normal and still screw the panel to the backboard. Then, in the future, if it needed to be reversed, you can unscrew the panel and there is a solvent that will e...
- Tue 24 May, 2022 6:29 pm
- Forum: Help!
- Topic: Cheap supermarket baby powder works well for thickening chalky emulsion paints.
- Replies: 7
- Views: 1074
Re: Cheap supermarket baby powder works well for thickening chalky emulsion paints.
Pva and Whiting can both be delivered to your door. (Or a neighbour) Tbh, and i don't want to sound mean, but you really need to consider retiring. If you are honest, you have not reopened your shop in 3 years. If you are struggling as much as you say above, then you really should not be operating t...
- Thu 19 May, 2022 6:50 pm
- Forum: Help!
- Topic: Keeping the oak grain when painting it
- Replies: 5
- Views: 787
Re: Keeping the oak grain when painting it
I suspect it is the wire wool causing the paint to grey.
What paint are you using. I use daler titanium white acrylic and watered down, should leave grain showing.
Just liberon black bison neutral wax and buffed with a yellow duster.
Nick
What paint are you using. I use daler titanium white acrylic and watered down, should leave grain showing.
Just liberon black bison neutral wax and buffed with a yellow duster.
Nick
- Tue 17 May, 2022 5:36 pm
- Forum: Help!
- Topic: Products to stain barefaced oak
- Replies: 23
- Views: 2495
Re: Products to stain barefaced oak
Top one, i would use van dyke crystals to make my own stain. A few quid and then crystals and boiling water to mix. Just play around with quantity of crystals to water. Then brush on and use liberon black bison neutral (not clear) wax. https://www.building-supplies-online.co.uk/liberon-van-dyck-crys...
- Mon 16 May, 2022 8:28 pm
- Forum: General Discussion
- Topic: Pilkington Glass
- Replies: 6
- Views: 1780
Re: Pilkington Glass
I think they may have stopped doing 2mm, but not 100% sure. The reason i think they may have is that my glazing company get my double glazed units and toughened glass from pilkington. They also do the self cleaning glass for conservatories. Where do they get their 2mm glass from? Wessex pictures of ...
- Wed 11 May, 2022 9:14 pm
- Forum: Help!
- Topic: Stiffening up the fence on my exising table saw.
- Replies: 12
- Views: 1867
Re: Stiffening up the fence on my exising table saw.
The position of the fence should not generally be positioned the full size of the saw. It is ok for cutting sheet material as that is stable and will not bind. When ripping timber, the fence should end at the midpoint of the blade, although i do keep mine towards the back of the blade. This is done ...
- Mon 02 May, 2022 9:03 am
- Forum: Help!
- Topic: Commercially produced strut backs
- Replies: 9
- Views: 1303
Re: Commercially produced strut backs
Agree with Steve. For anything close or over A4 that needs to sit on furniture rather than hanging, i make a base. 20180926_142953.jpg I cut an angled groove for the frame to sit in and provided the base goes back beyond the top of the frame, physics is on your side and it is completely stable. The ...
- Mon 18 Apr, 2022 7:48 am
- Forum: Help!
- Topic: Getting the absolute best cut mitres when cutting oak on a Morso.
- Replies: 4
- Views: 797
Re: Getting the absolute best cut mitres when cutting oak on a Morso.
I agree with above and that a morso will get a better cut than hand saw. I use Japanese saws mainly and they have much thinner blades than equivalent tenon saw, but i would go with morso every time.
Nick
Nick
- Sun 17 Apr, 2022 6:55 pm
- Forum: The Good, The Bad, And The Ugly
- Topic: Hogarth Frames
- Replies: 12
- Views: 4720
Re: Hogarth Frames
Thanks for details. I have seen that effect a fair few times, but didn't think it was going to be sand.
Cheers
Nick
Cheers
Nick
- Sun 17 Apr, 2022 4:38 pm
- Forum: The Good, The Bad, And The Ugly
- Topic: Hogarth Frames
- Replies: 12
- Views: 4720
Re: Hogarth Frames
Hi Dermot,
How did you apply the sand and what type of sand? Do you sprinkle onto pva or anything before covering in gesso? I really like the finish it gives.
Nick
How did you apply the sand and what type of sand? Do you sprinkle onto pva or anything before covering in gesso? I really like the finish it gives.
Nick
- Sun 17 Apr, 2022 8:05 am
- Forum: After Hours
- Topic: The importance of spacing
- Replies: 1
- Views: 3046
Re: The importance of spacing
Hilarious, there is no reason for it to be so squashed.
- Thu 14 Apr, 2022 6:59 pm
- Forum: The Good, The Bad, And The Ugly
- Topic: Hogarth Frames
- Replies: 12
- Views: 4720
Re: Hogarth Frames
Lovely job Dermot, and very interesting to see the amount of work involved in the making of those frames.
Your prize for finishing them is you get to make another 8!
Nick
Your prize for finishing them is you get to make another 8!
Nick
- Tue 12 Apr, 2022 7:50 pm
- Forum: Help!
- Topic: Worried about the weight
- Replies: 24
- Views: 5229
Re: Worried about the weight
Thanks for posting moulding. I would be pretty sure you are fine. There is plenty of surface to get a good strong joint. If you have a strap clamp, i would follow justintime's advice and use it.
Cheers
Nick
Cheers
Nick
- Tue 12 Apr, 2022 5:07 pm
- Forum: Help!
- Topic: Worried about the weight
- Replies: 24
- Views: 5229
Re: Worried about the weight
I think we could all be over complicating this, but without the exact size of the moulding being used, it is difficult to know. I picked up a spare piece of 4mm laminated glass in my workshop today to check its weight ( it was 50cm by 110cm) and i reckon i would happily have that is an obeche frame ...
- Tue 12 Apr, 2022 8:05 am
- Forum: Help!
- Topic: Worried about the weight
- Replies: 24
- Views: 5229
Re: Worried about the weight
Once pinned, the glue will hold the the joint together and generally most glue is stronger than the timber these days. Just make sure you apply glue first to joints, leave 3-5 minutes before joining the frame. Glue will soak up into end grain so apply a little first to soak in a seal. If you are wor...
- Mon 11 Apr, 2022 9:41 am
- Forum: Help!
- Topic: Cutting and joining hexagonal and octagonal frames.
- Replies: 12
- Views: 1413
Re: Cutting and joining hexagonal and octagonal frames.
I use mdf for panels inside cupboard doors and use zinsser bullseye primer & sealer. It is water based and requires no other sealer.
It can also be sprayed on for a neat finish, but if there is a smaller amount, i use a mini roller.
Nick
It can also be sprayed on for a neat finish, but if there is a smaller amount, i use a mini roller.
Nick
- Fri 08 Apr, 2022 10:57 am
- Forum: Help!
- Topic: Opinons please. Oscillating multi-tools
- Replies: 6
- Views: 1126
Re: Opinons please. Oscillating multi-tools
In a word, no.
I use them all the time for when on a site for window and door fitting and other carpentry jobs. However, i don't use them in my workshop when making the doors etc. And although i have them, i have never had a reason to need one for framing.
Nick
I use them all the time for when on a site for window and door fitting and other carpentry jobs. However, i don't use them in my workshop when making the doors etc. And although i have them, i have never had a reason to need one for framing.
Nick