Glass cutting
-
- Posts: 257
- Joined: Mon 27 Jul, 2009 12:54 pm
- Location: Bishop's Waltham & Stockbridge Hampshire
- Organisation: Hampshire Framing Limited
- Interests: .
- Contact:
Glass cutting
On the Excalibur I sometimes find that although the sheet is scored right the way down it doesn't break cleanly, typically at the start ie top of the score the glass breaks at a slight angle away from the clamp. The result is a small nib preventing the sheet from fitting into its intended frame.
Re: Glass cutting
Try using a more even pressure across the score line so it snaps more uniformly on the machine. You can also take of the nibs with pliers.
-
- Posts: 673
- Joined: Mon 29 Nov, 2010 12:20 pm
- Location: Halifax, West Yorkshire
- Organisation: Abacus Picture Framing and Gallery
- Interests: Picture Framing, Furniture making.
Re: Glass cutting
I don't think you are supposed to use the clamp with glass (the fletcher I use has "do not use for glass" on the clamp).
If i've misunderstood, please accept my apologies.
If i've misunderstood, please accept my apologies.
Re: Glass cutting
I always have - (on the keencut) it still scores unclamped but there is a chance of movement.
You may need a new wheel or a drop of oil on the one you have or to adjust the tension, maybe in addition to one of those. Put a piece of mount board behind the glass, that will effectively increase the tension, see what happens, if it improves things increase the tension.
You may need a new wheel or a drop of oil on the one you have or to adjust the tension, maybe in addition to one of those. Put a piece of mount board behind the glass, that will effectively increase the tension, see what happens, if it improves things increase the tension.
- IFGL
- Posts: 3087
- Joined: Sun 06 May, 2012 5:27 pm
- Location: Sheffield UK
- Organisation: Inframe Gallery Ltd
- Interests: Films ,music and art, my wife and kids are pretty cool too.
- Location: Sheffield
- Contact:
Re: Glass cutting
what roboframer said is exactly right, the clamp on the Excalibur is designed for glass clampage
in addition to his very good advice, you may need to adjust the baring screws if there is play in the head, correctly adjusted the glass should only need very slight pressure to snap it cleanly.
in addition to his very good advice, you may need to adjust the baring screws if there is play in the head, correctly adjusted the glass should only need very slight pressure to snap it cleanly.
-
- Posts: 10
- Joined: Mon 13 Jan, 2014 11:34 pm
- Location: Newcastle Australia
- Organisation: Pro-Am Colour
- Interests: Framing
Re: Glass cutting
I had the same problem for a while and an older framer suggested just to run the score a couple of times at the top for about 5cm then the full length as you would do normally. (hope that makes sense) it works a treat.
- GeoSpectrum
- Posts: 2151
- Joined: Fri 01 Oct, 2010 11:49 am
- Location: Lincolnshire
- Organisation: Ashcraft Framing
- Interests: Family, x-country skiing, wine, art, Jazz
- Location: Gainsborough, Lincolnshire
- Contact:
Re: Glass cutting
I found that happened but at the bottom, I found I was pressing on the glass a bit too high, I just moved my hand down a bit and the problem went away.
Alan Huntley
Ashcraft Framing
Bespoke Easels and Self-assembly tray frames
http://www.ashcraftframing.co.uk
Ashcraft Framing
Bespoke Easels and Self-assembly tray frames
http://www.ashcraftframing.co.uk
-
- Posts: 11019
- Joined: Sat 25 Mar, 2006 8:40 pm
- Location: Devon, U.K.
- Organisation: The Dartmoor Gallery
- Interests: Lost causes, saving and restoring old things, learning something every day
- Location: Glorious Devon
Re: Glass cutting
This problem happens from time to time on my system 4000, but I have found that the problem goes away when I lubricate the cutting wheel and axle with a quick squirt of GT85.
I think this must have something to do with how freely the wheel is able to revolve.
(GT85 does not contain oil, so it does not ruin the nylon cutting wheel housing).
I think this must have something to do with how freely the wheel is able to revolve.
(GT85 does not contain oil, so it does not ruin the nylon cutting wheel housing).
Mark Lacey
“Life is short. Art long. Opportunity is fleeting. Experience treacherous. Judgement difficult.”
― Geoffrey Chaucer
“Life is short. Art long. Opportunity is fleeting. Experience treacherous. Judgement difficult.”
― Geoffrey Chaucer