Hi all
Can anyone recommend a technique or method that will allow for neat looking knots and consistency in hanging height which also allows for variations in the angle of the cord as set out in the cord angle/downward force diagram on the wiki here?
Ideally I would like to be able to hang a number of frames together with the same dimensions on a row of independent horizontal wall fixings and have them all as level as possible so that their hanging position is interchangeable if required.
I know that there are other types of fixings that will allow this with greater ease but if it's possible by other means that are less costly I'd like to give that a go first.
Cheers
Mike
Consistent hanging height with cord.
-
- Posts: 62
- Joined: Tue 26 Jan, 2016 3:23 pm
- Location: Brookenby
- Organisation: Game of Frames
- Interests: All things zombie. I also do data recovery.
Re: Consistent hanging height with cord.
It's nigh-on impossible to tie wire/cord on a number of frames so that they all hang precisely level.
What you could try is making a hanging jig. Get a bit of thick board that will serve as a'wall'. Put a wall hook in it or two if applicable.
Hang the picture on these hooks and mark on the board where the top comes to. Measure between the hook(s) and the mark.
If you stretch a bit of string (tight as poss and level) along the wall as measure down to the difference on the board, you should be able to
hang a row of pictures level along the tops.
What you could try is making a hanging jig. Get a bit of thick board that will serve as a'wall'. Put a wall hook in it or two if applicable.
Hang the picture on these hooks and mark on the board where the top comes to. Measure between the hook(s) and the mark.
If you stretch a bit of string (tight as poss and level) along the wall as measure down to the difference on the board, you should be able to
hang a row of pictures level along the tops.
Watch Out. There's A Humphrey About
-
- Posts: 130
- Joined: Fri 27 Apr, 2012 5:42 pm
- Location: Reigate, Surrey, England
- Organisation: Cliff Baughen
- Interests: Photography, Picture framing
Re: Consistent hanging height with cord.
Would one of these https://www.lionpic.co.uk/p/11586/rekta ... -Placer--1 help?
- Steve N
- Posts: 2992
- Joined: Sat 21 Jul, 2007 2:32 pm
- Location: Somewhere Staple Hill Bristol
- Organisation: Frontier Picture Frames ltd
- Interests: Walking our retired Greyhound,art, falling asleep on sofa in front of the telly
- Location: Now in Bristol
- Contact:
Re: Consistent hanging height with cord.
Steve CEO GCF (020)
Believed in Time Travel since 2035
Proud to sell Ready Made Frames
http://www.frontierpictureframes.com
http://www.designerpicturemounts.com/
Believed in Time Travel since 2035
Proud to sell Ready Made Frames
http://www.frontierpictureframes.com
http://www.designerpicturemounts.com/
- David McCormack
- Posts: 1442
- Joined: Tue 02 Aug, 2011 10:14 am
- Location: South Lakes
- Organisation: Framing
- Interests: Cycling, walking, darkroom photography and laughing a lot!
- Location: Cumbria
- Contact:
Re: Consistent hanging height with cord.
As Prospero says, getting the cord/wire on several frames to be the exact same length is nigh on impossible... so just do away with the cord!MikeSwannick wrote:...so that their hanging position is interchangeable if required.
...but if it's possible by other means that are less costly I'd like to give that a go first.
Fix your usual D-rings a bit higher than normal (say a quarter down from the top if you normally do a third) but set them facing vertically just like a strap hanger. You will need two wall hooks per frame. It is not difficult to precisely fix each D-ring in the same position on all the frames but care is needed to fix all the wall hooks level and the correct distance apart.
If successful, then each frame in the row can be interchanged with any other and remain at the same height.
Also, with reference to that wiki hanging diagram, when the cord is set at an angle of 60 degrees the downward force on each D-ring is 6lbs for a 10lb frame (i.e. 12lbs in total) but with the D-rings directly hanging on the wall hooks the force on each D-ring is just half the weight of the frame i.e. 5lbs!
For larger heavier frames I would buy in some strap hangers.
And those beehive hangers do look interesting... allowing for errors in wall hook position.
"You know, there's a right and wrong way to do everything!"
Oliver Hardy.
https://www.instagram.com/davidaustinmccormack/
Oliver Hardy.
https://www.instagram.com/davidaustinmccormack/
-
- Posts: 62
- Joined: Tue 26 Jan, 2016 3:23 pm
- Location: Brookenby
- Organisation: Game of Frames
- Interests: All things zombie. I also do data recovery.
Re: Consistent hanging height with cord.
Thanks for the replies. I did suspect that I might be chasing rainbows with this one but you never know.
thanks prospero - there is always room for another homemade jig
I like the vertical D rings idea David McC - thanks for that one.
I like the beehive products too Steve N.
If someone made the cord equivalent of the wire and crimping ferrules system, that would definitely help.
Mike.
thanks prospero - there is always room for another homemade jig
I like the vertical D rings idea David McC - thanks for that one.
I like the beehive products too Steve N.
If someone made the cord equivalent of the wire and crimping ferrules system, that would definitely help.
Mike.
- Rainbow
- Posts: 891
- Joined: Tue 23 Jun, 2015 8:51 am
- Location: See my name, I'm somewhere over it
- Organisation: Picture sales and framing
- Interests: varied
Re: Consistent hanging height with cord.
Thanks for the suggestion, baughen, I've just ordered one for a relative who's moving house and has dozens of pictures to re-hangbaughen wrote:Would one of these https://www.lionpic.co.uk/p/11586/rekta ... -Placer--1 help?