MORSO EH and KEENCUt 4000 FOR SALE

Buying/selling equipment
Situations wanted/vacant
Forum rules
All sellers are required to have a forum profile that identifies them clearly. (Such as - name, surname, location, business name et cetera)
Post Reply
Dean Casson
Posts: 45
Joined: Fri 08 Nov, 2013 2:09 pm
Location: Ashtead, Surrey
Organisation: CASSONS framing
Interests: painting, family, football, squash

MORSO EH and KEENCUt 4000 FOR SALE

Post by Dean Casson »

Hello,
I bought these 2 pieces of equipment May 2017 (both from the forum). The Morso has hardly been used in the past year, just turned on and warmed up each week and a few cuts made to keep the system in shape. The Keencut has not been used at all.

Morso EH fully automated cutter £3,000
Had full service oil change and filter, deep clean and ready to go.
2 x spare sets of genuine blades . Sharpened and ready from lion. 3 blades in total
1 x spare set of bottom blades sharpened and ready. 2 blades in total.
Has left hand extension table.
Single phase 240v.
IMG_0371.JPG
IMG_0371.JPG (2.26 MiB) Viewed 3137 times
IMG_0370.JPG
IMG_0370.JPG (2.02 MiB) Viewed 3137 times
IMG_0369.JPG
IMG_0369.JPG (1.92 MiB) Viewed 3137 times
IMG_0373.JPG
IMG_0373.JPG (2.8 MiB) Viewed 3137 times
IMG_0374.JPG
IMG_0374.JPG (1.82 MiB) Viewed 3137 times
Sorry about the pics being on the sides :roll:

Keencut 4000 Glass and Board cutter £200
Already dismantled but ready to go. With instructions.

I'm in Ashtead, Surrey about 1 mile from J9 M25.
Thanks
Dean
Buster
Posts: 35
Joined: Sun 30 Jul, 2017 12:58 pm
Location: Dorset
Organisation: DIY
Interests: Cycling, golf, art

Re: MORSO EH and KEENCUt 4000 FOR SALE

Post by Buster »

Hi, just to confirm..are you saying the 4000 is as new? and if so, is it the 48ins version and how big is it now dismantled (considering transport options) ?
Dean Casson
Posts: 45
Joined: Fri 08 Nov, 2013 2:09 pm
Location: Ashtead, Surrey
Organisation: CASSONS framing
Interests: painting, family, football, squash

Re: MORSO EH and KEENCUt 4000 FOR SALE

Post by Dean Casson »

Sorry probably wasn't clear enough, the Keencut is not new! The dismantled parts are a maximum length of 2200mm by approx 250mm section. I managed to get it my estate car when I picked it up. It's fairly bulky/heavy but I can help with it this end - you'd need a helping hand at the other. Will post a picture later.
Thanks
Dean
theprint.ninja
Posts: 31
Joined: Sat 23 Aug, 2014 2:09 am
Location: Dawlish, Devon
Organisation: The Print Ninja
Interests: I fly UAV's for arial photos, I spend my time printing high resolution canvasses and museum quality prints for private individuals and corporate clients alike

Re: MORSO EH and KEENCUt 4000 FOR SALE

Post by theprint.ninja »

Did you sell your EH ?
Dean Casson
Posts: 45
Joined: Fri 08 Nov, 2013 2:09 pm
Location: Ashtead, Surrey
Organisation: CASSONS framing
Interests: painting, family, football, squash

Re: MORSO EH and KEENCUt 4000 FOR SALE

Post by Dean Casson »

Apologies for the delay in reply - been upto my eyes in house renovation. The Morso is still for sale.
Thanks
Post Reply