Saying "Hello" and asking advice

Say hello, and tell us a little about yourself.
Post Reply
malcolmm
Posts: 2
Joined: Tue 13 Mar, 2012 4:12 pm
Location: Bedfordshire
Organisation: mirror frames/ Toddington
Interests: Phootgraphy and early retirement

Saying "Hello" and asking advice

Post by malcolmm »

Hi - I am just setting up and am about to agree to a £500 refurb on a used taurus underpinner. Before agreeing to this what does anyone think of the new Charnwood/framers corner M4. I will be using wide and sometimes heavy hard and softwood mouldings to frame mirrors. Any advice would be gratefully recieved - many thanks.

Malcolm
Top
FrameArt
Posts: 46
Joined: Tue 05 Jul, 2005 8:32 pm
Location: Powys

Re: Saying "Hello" and asking advice

Post by FrameArt »

Hi Malcolm,

Welcome to the forum, sorry I can't answer your question about the M4 underpinner.

All the best,
Arthur
FrameArt
Top
User avatar
birdman
Posts: 684
Joined: Thu 07 Jun, 2007 2:41 pm
Location: Tandragee, Co Armagh
Organisation: Pelican Picture Framing
Interests: Getting up close and personal with Val
Location: N. Ireland
Contact:
Contact birdman

Re: Saying "Hello" and asking advice

Post by birdman »

Hi Malcolm, welcome to the forum.

I too am unable to comment on the equipment you mentioned because we use another product. Sorry you haven't had a response to your question yet, that is very unusual on this forum and it might be that the question has been missed because it is in the introduction area.

It might be worth asking the question again under the "Help" topic area if it isn't too late to help you with your decision.

Good luck with your venture.

Rolf
Rolf Lawson GCF
“I am playing all the right notes, but not necessarily in the right order.” Eric Morecambe
My status
Top
User avatar
David McCormack
Posts: 1442
Joined: Tue 02 Aug, 2011 10:14 am
Location: South Lakes
Organisation: Framing
Interests: Cycling, walking, darkroom photography and laughing a lot!
Location: Cumbria
Contact:
Contact David McCormack

Re: Saying "Hello" and asking advice

Post by David McCormack »

On this thread a forum member, countrystudio, mentions they use an M4, you could PM them and get some feedback on it.

http://theframersforum.com/viewtopic.php?f=6&t=6825
"You know, there's a right and wrong way to do everything!"
Oliver Hardy.
https://www.instagram.com/davidaustinmccormack/
Top
User avatar
GeoSpectrum
Posts: 2172
Joined: Fri 01 Oct, 2010 11:49 am
Location: Lincolnshire
Organisation: Ashcraft Framing
Interests: Family, x-country skiing, wine, art, Jazz
Location: Gainsborough, Lincolnshire
Contact:
Contact GeoSpectrum

Re: Saying "Hello" and asking advice

Post by GeoSpectrum »

I use the M3 which is fine for every day moulding, but doesn't cope well with hard wood so I may upgrade in the future. I think the M4 is beefed up a bit and sould be fine. It has a handy way of swapping v-nails via a cartridge system I think, the M3 is a bit fiddly in this respect. I don't find the clamp on mine much use, it may be better on the M4. On the whole for 600 quid new you could do worse.
Alan Huntley
Ashcraft Framing
Bespoke Easels and Self-assembly tray frames
http://www.ashcraftframing.co.uk
Top
Graysalchemy

Re: Saying "Hello" and asking advice

Post by Graysalchemy »

I would pay a bit more and get a new cassese. By far the best machines on the market IMHO
Top
Post Reply

Return to “Introductions”