Hi all, bit of a curve ball.
I’ve seen mounts with the artists logo embossed into it via a press. I’ve just messaged a company that makes these presses but say theirs won’t emboss mounts as they are too thick.
Has anyone done this for a customer? Done it themselves or know of a company that can supply these presses? Its for my own mounts and artwork
Thanks
Dave.
Embossed logo.
-
- Posts: 22
- Joined: Sat 27 Jun, 2020 2:41 pm
- Location: Shropshire.
- Organisation: Hobbyist.
- Interests: Paper cutting artist for 12 years, used a Logan 655 for about 6 years (don’t shoot me....) to mount my own work.
Interested in framing and mounting methodology.
-
- Posts: 1315
- Joined: Thu 23 Sep, 2004 8:31 pm
- Location: Detroit, Michigan USA
- Organisation: minoxy, LLC
- Interests: non-fiction knowledge
- Contact:
Re: Embossed logo.
Any machinest's "arbor press" will have enough force to emboss paper or mat board.
The question is in obtaining a die in the image of the artists logo and what it will cost to make that die.
The question is in obtaining a die in the image of the artists logo and what it will cost to make that die.
Jerome Feig CPF®
http://www.minoxy.com
http://www.minoxy.com
-
- Posts: 22
- Joined: Sat 27 Jun, 2020 2:41 pm
- Location: Shropshire.
- Organisation: Hobbyist.
- Interests: Paper cutting artist for 12 years, used a Logan 655 for about 6 years (don’t shoot me....) to mount my own work.
Interested in framing and mounting methodology.
Re: Embossed logo.
Thanks Jerome. Just had a look, arbor presses are reasonably priced and the company that I enquired at makes the dies, it was just a case that their presses didn’t exert enough force to imprint the mount board. I guess if I can’t find a hand press, that’s a Plan B.
Many thanks.
Dave.
Many thanks.
Dave.
- Steve N
- Posts: 2992
- Joined: Sat 21 Jul, 2007 2:32 pm
- Location: Somewhere Staple Hill Bristol
- Organisation: Frontier Picture Frames ltd
- Interests: Walking our retired Greyhound,art, falling asleep on sofa in front of the telly
- Location: Now in Bristol
- Contact:
Re: Embossed logo.
why not send the (press) company a sample of mount , then get them to have a go at embossing it
Steve CEO GCF (020)
Believed in Time Travel since 2035
Proud to sell Ready Made Frames
http://www.frontierpictureframes.com
http://www.designerpicturemounts.com/
Believed in Time Travel since 2035
Proud to sell Ready Made Frames
http://www.frontierpictureframes.com
http://www.designerpicturemounts.com/
-
- Posts: 22
- Joined: Sat 27 Jun, 2020 2:41 pm
- Location: Shropshire.
- Organisation: Hobbyist.
- Interests: Paper cutting artist for 12 years, used a Logan 655 for about 6 years (don’t shoot me....) to mount my own work.
Interested in framing and mounting methodology.
Re: Embossed logo.
Thanks Steve, good idea. I thought I could get a die that they sell for wax seals which is made from brass, remove it, solder it onto the end of a brass bar then just give it a tap with a hammer to emboss it but the text is engraved into it as opposed to raised up from the face so I don't think it would work as well.
I’ll see if they would consider a test run on a piece of Mount board. They have a “Notary” hand press for up to 250gsm which might be enough to emboss although that is obviously nowhere near mount board thickness
Dave.
I’ll see if they would consider a test run on a piece of Mount board. They have a “Notary” hand press for up to 250gsm which might be enough to emboss although that is obviously nowhere near mount board thickness
Dave.
-
- Posts: 22
- Joined: Sat 27 Jun, 2020 2:41 pm
- Location: Shropshire.
- Organisation: Hobbyist.
- Interests: Paper cutting artist for 12 years, used a Logan 655 for about 6 years (don’t shoot me....) to mount my own work.
Interested in framing and mounting methodology.
Re: Embossed logo.
Thanks Jerome, seen quite a few on Amazon/ Ebay etc.
Dave.
Dave.